Acmos Chemie KG

Postfach 101069, 28010 Bremen
Industriestr. 49, 28199 Bremen
Germany
Telephone +49 421 5189-0
Fax +49 421 511415
acmos@acmos.com

Hall map

glasstec 2018 hall map (Hall 12): stand C13

Fairground map

glasstec 2018 fairground map: Hall 12

Contact

Marina Littau

technical Sales

Phone
+49 421 5189 212

Email
mlittau@acmos.com

Our products

Product category: Aids for the forming of hollow glass

ACMOS® cooling lubricant for feeder blades

ACMOS® cooling lubricants for feeder blades are based on native oils or are fully synthetic.
Depending on dosing system you use and the required dilution ratio you can choose between a broad range of products.
After optimal implementation the following advantages can be obtained:
 
Excellent lubricating and cooling effect at a dilution ratio up to 1:2000
High corrosion protection
Long feeder blade life
Robust against micro-organisms
Excellent glass cut-off
Very low consumption

Please see also our information sheed attached.

More Less

Product category: Aids for the forming of hollow glass

ACMOS® high thermal resistance special coatings for moulds (blanks, neck rings etc.)

ACMOS special coatings are varnish types, highly heat-resistant coatings, specially developed for surface treatment of moulds.
ACMOS special coatings form a matt grey, very strong adhering film, which enables dry closing of the moulds and renders mould lubrication unnecessary for many hours.

After optimal implementation the following advantages can be obtained:

Reduction of glass defects / less cracks and checks
Considerably improved sliding properties of the glass
Easy loading and blowing out without cracks on the glass surface
Protects mould surface against corrosive attack of molten glass
Significant quality improvement of the final articles
Reduces consumption of release agent, as a frequent swabbing can be eliminated for many hours (up to 5 hours) after putting the mould into service
Less swabbing material applied => less built-up in the mould => extended running time of the moulds

Please see also our information sheet attached.

More Less

Product category: Aids for the forming of hollow glass

ACMOS® coatings for chutes

ACMOS coatings for chutes are strong and heat-resistant two-component coatings, especially developed for surface treatment of the chutes.
Because of the coating’s extremely good impact strength and heat resistance, the lifetime of the chutes can be extended to several weeks. ACMOS coatings for chutes cope well with extreme heat loading due to high cutting speeds.
The friction between the gob and the chute surface can be decreased, so that the sliding properties of glass gobs in the chute can be improved considerably.

After optimal implementation the following advantages can be obtained:
Better sliding of glass gobs in the chute
Less friction between the gob and the chute surface
The gob slides easily and reaches the mould at a more constant speed

Please see also our information sheet attached.

More Less

Product category: Aids for the forming of hollow glass

ACMOS® 43-5004 Chute Repair Coating Agent

With ACMOS 43-5004 the impact surfaces of the drop chutes worn by the glass gob can be repaired. Article defects like loading marks, washboards etc., which are due to the worn chutes, are minimized significantly by the use of ACMOS 43-5004.
The application of the coating is easy and takes only low influence on production process! A cooling of the preforms by the ejected gob is hardly measurable. Test runs in several glassworks have shown that an application in an interval of four hours can be sufficient to exploit the advantages of the coating extremely well. However, the coating can be also used according to demand.

Please see also the information sheet attached.

More Less

Product category: Aids for the forming of hollow glass

ACMOS® Release agent for blank moulds

 ACMOS® Release agent for blank moulds
… are based on a graphite-mineral oil with best flow and wetting properties on the hot blank mould
… are very economical in use and very efficient
… form a very thin, uniform coating that adheres well and does not split off
… extend swabbing intervals without obstruction of heat transfer to the mould, which is one of important conditions for an optimal glass dispersion
… reduce cracks, make bottles surface smooth and shiny
… can also be used for neck rings, blank mould bottoms and funnels

Please see also the file attached.

 

More Less

Product category: Aids for the forming of hollow glass

Spraying instead of swabbing with ACMOS 48-417, 48-418 and 48-419

By using  ACMOS 48-417, 48-418 and 48-419 as an alternative for swabbing you can achieve many advantages:

Coating is more uniform, no defects on glass surface
Significant scrap reduction
Extension of greasing cycle
Low consumption of Release Agent
Less build-up in the mould
Pre-coating stays in the mould for a longer time
Smooth loading process
Better reliability of production process  
Greasing interval can be doubled

Please see also the information attached.

More Less

Product category: Aids for the forming of hollow glass

ACMOSOL® 130 - 28 Cleaner for moulds

ACMOSOL 130-28 is a highly effective cleaner specially developed for degreasing glass moulds.

Because of the very slow evaporation, the cleaning effect is very good. This ensures better adhesion between the mould varnish and the mould and increases service life.

ACMOSOL 130-28 can also be used for cleaning the spray gun.

See also the file attached.
 

More Less

Product category: Aids for the forming of hollow glass

Special coating resistant to high temperatures for finished moulds

ACMOS 43-34 is a varnish-like, highly heat-resistant coating specially developed for surface treatment of finished moulds and their bottoms. Application of ACMOS 43-34 prevents micro‑cracks, particularly in lettering and engravings.
The life is several days !

Please see the file attached for further information.

More Less

Product category: Aids for the forming of hollow glass

ACMOS® 48 - 141 Release agent for finished moulds

ACMOS 48-141 is a mould release paste with excellent flow and wetting properties on the hot finished mould.
ACMOS 48-141 forms an extremely thin, but uniform parting film, which adheres very well and prevents cracks in the glass. Heat transfer to the mould is not impeded.

Bottles and glasses made with ACMOS 48-141 are smooth and lustrous.

Please see our information sheet attached.

More Less

Product category: Aids for the forming of hollow glass

ACMOS® products for neck rings

Special heat-resistant coating
ACMOS 43-2414 is a paint-type, highly heat-resistant coating, which was specially developed for surfaces heat-treatment of neck rings.
ACMOS 43-2414 forms a silvery firmly adhering film, which renders lubrication unnecessary and prevents micro-crack on the articles.

Release Agents for neck rings, neck joints and engraving.
The ideal method is to apply to newly commissioned neck ring shaping tools, which must be hot at the time. To lubricate the neck ring the machine should be stopped and coated with a small swab.
Once applied ACMOS Release Agent builds a thin coat, which helps to prevent cracks and checks on rings and neck joints caused by an opening of the moulds or a loss of glass temperature.
As only high quality raw materials are used, ACMOS Release Agent can be used as a starter but also for an interval application (touching-up) during the production process.

Please see the file attached for further information.

 

More Less

Product category: Aids for the forming of hollow glass

ACMOSIN® Anti-corrosion and lubricating agents

ACMOSIN 52-46 Anti-corrosion and lubricating agent for annealing furnace mats
ACMOSIN 52-46 is an aqueous dispersion of special active ingredients. During use existing rust is bound and a new formation is effectively prevented.
ACMOSIN 52-46 contains a small amount of graphite in order to guarantee better sliding when glass articles are inserted into the furnace.

ACMOSIN 51-14 Anti-corrosion agent for tools (moulds, neck rings etc.)
was specially developed as corrosion protection for unused tools.
Please apply ACMOSIN 51-14 on tool surface and let it dry before storage.
A removal of existing corrosion protection layers is thereby unnecessary.

See also the file attached.

More Less

Product category: Aids for the forming of hollow glass

ACMOS® Special coating for conveyor belts (hot-end)

ACMOS Special coating for conveyor belts is a dispersion of waxes and graphite in water, with a very well adhesion on metal. It is preferably used on the hot end conveyor belts and prevents the cracking in the glass bottom. 

ACMOS Special coating for conveyor belts serves as protection of the contact points between glass and metal e.g. on the transport from production into the annealing furnace and for the transfer plate.

It has therefore to be used particularly at bottles which shall resist an inside bursting pressure.

 Please see also the file attached.

More Less

Product category: Aids for the forming of hollow glass

ACMOS® Lubricants for metal / plastic conveyor belts

ACMOS lubricants for conveyor belts increase the sliding effect and protect the glasses or bottles against surface damage.

ACMOS 23-5100 is a water-based, polishable wax product, which can be sprayed on guide rails and conveyor belts at the cold end.

ACMOS 82-2405 is a wax-based spray, especially developed for application on guide rails and belts for sliding effect improvement.
ACMOS 82-2405 is silicone-free!

Please see the file attached for further information.
 
 

 

More Less

Product category: Aids for the forming of hollow glass

ACMOS® Products for rotary blowing machines

ACMOS – special coating for rotary blowing machines
ACMOS 43-102 (2-component system, spreadable)
ACMOS 43-104 (1-component system, spreadable)
are high-quality coatings for rotary blowing machines, which help you to extend running time of the moulds to 24 hours and longer.

Wetting and sliding agent for rotary blowing machines
ACMOS 133-53 is an additive for cooling water to improve surface tension and creep behaviour of water, which has a positive impact on steam buffer appearing in the mould.

High temperature-resistant special coating for moulds
ACMOS 43-2450 is a varnish-like, highly heat-resistant coating, which was specially developed for coating the surface of used rotary finished moulds to improve the sliding effect of the parison.

Please see the file attached for further information.
 

More Less

About us

Company details

ACMOS CHEMIE KG furthers the manufacture of moulded parts by means of effective release agents and rational processing aids.
ACMOS has a team of application experts ready to assist in the development and introduction of new moulding technologies – even on-site and in production facilities.

Do you require any advice or would you like more information on products or samples for your production processes?

Visit us!

More Less

Company data

Export content

> 75%

Number of employees

101-500

Area of business

Glass manufacture/production technology

Target groups

Hollow Glass